In this paper SiC particle reinforce aluminum metal matrix composite welded using high power continuous laser. Microstructure of laser beam welded SiC/Al MMC is characterized as functions of laser processing parameters. Results show that sound weld with little pores can be produced by laser beam welding, while aluminum carbide is formed in the weld. The size and the volume fraction of aluminum carbide are proportional to the laser power density. direction of shielding gas flow has significant effect on weld quality and weld microstructure.

Experimental and numerical investigations have been performed to study the natural convection heat transfer from a longitudinal fin arrays at different orientation angles. For such purpose, an experimental test rig was manufactured to be used for these investigations. It basically consists of base plate, an array of parallel longitudinal fins, heating unit and layers of thermal insulation. During the experiments, the fin spacing (S) was varied from 3.375 to 33 mm, while the fin height (H) from 15 to 60 mm. The orientation angle (Ф) was changed from 0° to 180°, and temperature difference between fin and surrounding (∆T) from 35 to 95 °C. To understand the general flow patterns dominating flows from the heat sink, the three-dimensionless elliptic governing equations were solved using finite volume computational fluid dynamics (CFD) code. A comparative study between the experimental and numerical results was performed to verify the numerical code. It was found for the configuration tested that the heat transfer rate per unit base area increases with the increase in the fin spacing and reaches a maximum value then decreases with farther increase in the fin spacing. The maximum heat dissipation occurs at optimal spacing 5. 6 S opt = mm. Moreover, the average heat transfer coefficient was found to have a maximum value at Ф = 0° and decreased with the increase of (Ф) to reach a minimum value at Ф = 90°. Empirical correlations between Nussult number, Rayleigh number, fin spacing, fin height, orientation angle, temperature difference between the fin and surroundings were derived.

In this paper a low complexity MIMO MC-CDMA receiver is proposed. We investigate the receiver performance and complexity in the case of despreading multicarrier code division multiple access signals (MC-CDMA) prior to V-BLAST detection in multiple input multiple output systems (MIMO). The proposed structure shows that for iterative detection, despreading before detection (DBD) reduces the effect of multiple access interference (MAI), and the reported results demonstrate improved bit error rate (BER) performance and user capacity of the system over despreading after detection (DAD). Furthermore, DBD results in reduced system complexity. The performance of both detectors is evaluated using computer simulations for a frequency selective slow Rayleigh fading channel.

The present study was performed to evaluate the anti-schistosomal activity of the medicinal plant ginger Zingiber officinale. Mice were individually infected with 100 Schistosoma mansoni cercariae. Four weeks post-infection, mice were orally treated with 1200 mg/kg of ginger for ten consecutive days. After the last dose all animals were sacrificed to evaluate the efficacy of ginger in treatment of the infection. The results obtained showed moderate reduction of 16.5% in the worm burden compared with control infected animals. The liver egg count showed a marked reduction of 53.8%. Ginger treatment showed a significant reduction in the size of liver granuloma where a percentage reduction of 66.35 was observed. Ginger treatment was slightly reflected on the liver function at such rate of infection, where an improvement in serum arginase activity was recorded, while no appreciable improvement in hepatic ALT and AST activities, albumin and creatinine contents. In conclusion Z. officinale displayed some degree of anti-schistosomal activity through reducing of the S. mansoni eggs output and the liver granuloma size.

Parallel plate combustor wall cooling was investigated. The combustor air flowed down the gap between two flat surfaces in a low pressure loss configuration. The work was aimed at combustor liner external air cooling for regenerative combustor cooling prior to entering a lean low NOx combustor. The test rig was 152 mm square and the test section was a duct of 152mm width and height of 10 and 5mm with a 152mm length. The experimental investigation involved the measurement of the heat transfer coefficient using the lumped capacity method. together with overall wall cooling effectiveness measurements in a hot duct test rig. The compromise between increased pressure loss and enhanced heat transfer for obstacles in the duct was investigated. It was shown that at coolant flow rates comparable with combustor requirements, adequate wall cooling effectiveness could be achieved using this technique. The cooling effectiveness performance was compared with the alternative technique of impingement cooling using low impingement jet pressure loss